Printing a colour negative in the darkroom uses the same enlarger, easel and habits as black and white printing. Three things change: you work in the dark, the developer must be held at a set temperature, and you balance the colour of the print with filters. This guide takes you from a black and white printer's skills to a first good colour print on RA-4 paper.
RA-4 is the process for colour negative paper. Every figure below comes from a maker's data sheet or leaflet, named beside it and listed under Sources. Where the makers disagree, both are shown. The makers say little about the order of work at the enlarger, so that part also draws on named printers' published accounts.
- Colour developer is harmful if swallowed and can cause skin allergy. Wear nitrile gloves and eye protection, and use tongs or a drum so your hands stay out of the solutions
- Ventilate the room, and never eat or drink where you work
- Read the safety data sheet supplied with your kit before you mix it
- Keep used solutions in labelled bottles for disposal. See Safety and Disposal in the UK below
How colour printing differs from black and white
If you have followed Print Exposure Basics, you already know how to set up an enlarger, make a test strip and judge exposure. Colour printing adds four things.
- Darkness. Kodak and Fujifilm both say to handle RA-4 paper in total darkness. There is no comfortable safelight as there is for black and white paper.
- Temperature. The developer is used warm, and Kodak asks you to hold it within 0.3°C of the temperature you choose.
- Two baths. The paper is developed, then cleared in a combined bleach and fixer called bleach-fix or blix, then washed.
- Colour balance. There are no contrast grades to choose. You change the colour of the enlarger's light with filters until the print is neutral.
The paper is chromogenic: the image is made of cyan, magenta and yellow dye layers. Kodak notes one practical result, which is that you cannot reduce density with an etching knife as you can on a black and white print.
What you need
- Enlarger with a colour head or a filter drawer
Kodak says to control colour with dichroic filters built into the enlarger, or with colour printing (CP) filters placed between the lamp and the negative. The lamp should be tungsten or tungsten-halogen. Kodak says not to use fluorescent lamps, and to fit heat-absorbing glass.
- Enlarging lens, easel, timer and focus finder
The same ones you use for black and white. Cover or switch off anything that glows.
- RA-4 colour paper
See Buying Paper and Chemistry in the UK below.
- RA-4 chemistry
A colour developer and a bleach-fix. A stop bath of dilute acetic acid is optional in trays; Kodak expects one in drums.
- A drum, a set of trays or a roller processor
A drum lets you work with the lights on once the paper is loaded. Trays mean working in the dark until the bleach-fix is done.
- Accurate thermometer and a water bath
Kodak, Tetenal, Bellini and ADOX all set the developer at or near 35°C. Kodak and ADOX give a tolerance of 0.3°C either way.
- Nitrile gloves and eye protection
Bellini and Tetenal both tell users to wear gloves and safety goggles.
- A viewing light
A lamp of about 5000 K with good colour rendering, used for every test strip and test print. See A viewing light below.
- Notebook
Write down the filter pack, aperture and time for every print. A negative you have balanced once can be printed again from your notes.
Enlarger and filters
A colour head has three dials: yellow, magenta and cyan. Each dial moves a dichroic filter into the light. If your enlarger has no colour head, Kodak's alternative is a set of CP filters in the filter drawer above the negative. You can stack any number of them there. If you use cyan filters, Kodak says to use the ones marked with the suffix "-2", for example CP10C-2.
As far as we know, no UK shop sells colour printing filter sets new. Used sets, and used enlargers with colour heads, are easy to find on eBay.
Kodak also advises a voltage regulator, because changes in mains voltage change both the brightness and the colour of the lamp. Mask the negative so no stray light passes around it.
Drum, tray or roller processor
- Drum or tube. You load the paper in the dark, close the drum and do the rest in room light. Kodak asks for at least 1200 ml of solution per square metre of paper, and for the tube to be completely dry before each sheet, because wet surfaces cause spots. See Rotary Processing for how drums are used.
- Trays. The simplest way to start, but every step up to the end of the bleach-fix happens in the dark. Kodak says that with practice you can process up to six prints together, or three if they are larger than 8 x 10 in.
- Roller processor. A tabletop machine that carries the paper through heated baths. Tetenal's leaflet gives 45 seconds in each bath at 35°C for the Durst, Metoform and Thermaphot machines it lists.
A viewing light
Set up the light you will judge by before the first session. A print judged under a warm household bulb will be corrected the wrong way. Both makers set out a viewing light, and they are close.
| Kodak | Fujifilm | |
|---|---|---|
| Colour temperature | 5000 K, give or take 1000 | 5000 K, give or take 300 |
| Colour rendering index | 85 to 100 | 90 or more |
| Brightness | At least 538 lux | 500 lux or more |
Kodak adds that you should evaluate prints under light of the same colour and brightness that the final print will be seen in. Use the same lamp for every test print. The colour temperature tool shows where common light sources sit.
Working in the dark
Both paper makers start from the same instruction: total darkness. They then allow a dim safelight only if you cannot manage without one, and they set different limits.
| Kodak (Endura Premier, J-39) | Fujifilm (Crystal Archive Type CA) | |
|---|---|---|
| First choice | Total darkness | Total darkness |
| Safelight filter | Kodak 13 (amber) | Two Fuji 103A filters, or Wratten 13 |
| Bulb | 7.5 W | 10 W tungsten |
| Distance | At least 1.2 m from the paper | At least 1 m from the work area |
| Time limit | "As short as possible" | No longer than 1 minute |
| Warning | "Using a safelight will affect your results." Test first | Paper that has already been exposed is fogged more easily |
For a first session, plan to work with no safelight at all.
- Find the stray light. Kodak says to eliminate light from enlarger heads, timers and LEDs. Sit in the dark room for a few minutes and tape over everything you can see.
- Lay things out the same way every time. Paper box, easel, drum or trays: learn where each one is with the lights on, then practise loading a scrap sheet with your eyes closed.
- Handle the paper by its edges. Kodak packed its sheet paper with the emulsion side of every sheet facing the same way, so note which way up the first sheet is.
- Process soon after exposing. Kodak expects no change in an exposed Endura Premier sheet kept between 5 seconds and 24 hours. Fujifilm is more cautious: keep the gap between exposure and development the same each time, and do not leave exposed paper until the next day.
The process: steps, times and temperatures
The standard process is short. These are the makers' own tables for a drum.
| Step | Time | Temp | Agitation |
|---|---|---|---|
| Prewet | 0:30 | 35°C | Rotary, in the processor with clean water |
| Developer | 0:45 | 35°C | Rotary |
| Stop bath | 0:30 | 35°C | Rotary |
| Wash | 0:30 | 35°C | Rotary |
| Bleach-fix | 0:45 | 35°C | Rotary |
| Wash | 1:30 | 35°C | Continuous flow with one complete change every 30 s, or three 30 s batch washes |
From Tray, Drum, and Rotary-Tube Processing with KODAK EKTACOLOR RA Chemicals. Run it step by step in the process timer.
| Step | Time | Temp | Agitation |
|---|---|---|---|
| Pre-warm the drum from the outside | 1:00 | 35°C | — |
| Colour developer | 0:45 | 35°C | Rotary |
| Stop bath (optional) | 0:15 | — | Rotary |
| Bleach-fix | 0:45 | 35°C | Rotary |
| Wash | 1:30 | 35°C | Three changes of 30 s |
From Tetenal Colortec RA-4 Professional Print Kit RT: instruction for use (Art. 102124). Run it step by step in the process timer.
The two disagree on one point. Kodak says that in drums and rotary tubes "the prewet and the stop-bath steps are necessary for optimum processing uniformity". Tetenal says not to pre-wash, because water left in the drum slows the developer, and warms the drum from the outside instead. Follow the instructions for the chemistry you are using.
Bellini's data sheet gives 45 seconds of developer at 35.0°C and 45 seconds of bleach-fix at 32 to 35°C. It then finishes with its stabiliser at 24 to 35°C: either two or three baths of about a minute each, or a running-water wash of at least 2 minutes followed by a last rinse in stabiliser. ADOX's page gives the developer temperature as 35°C, within 0.3°C, and says the bleach-fix is more tolerant. We could not find ADOX's own times. The instruction link on ADOX's page did not resolve, and the kit's safety data sheet gives hazards and storage (5 to 25°C for the concentrates) but no process times. Follow the leaflet in the box.
In trays
| Step | Time | Temp | Agitation |
|---|---|---|---|
| Developer | 1:00 | 33.3°C | Rock the tray gently side to side and end to end; lift the print 5 s before the end and drain |
| Stop bath (optional) | 0:30 | — | As developer |
| Wash (optional) | 0:30 | — | As developer |
| Bleach-fix | 1:00 | — | As developer |
| Wash | 1:30 | — | — |
From Tray, Drum, and Rotary-Tube Processing with KODAK EKTACOLOR RA Chemicals. Run it step by step in the process timer.
Kodak's tray method runs slightly cooler and longer than the drum method. Rock the tray gently from side to side and from end to end. Five seconds before each time is up, lift the print, let it drain and move it to the next tray. You can turn the room lights on after the bleach-fix.
Working at lower temperatures
You do not have to work at 35°C. Kodak gives a set of matched developer times and temperatures, and says any of them is acceptable as long as you hold the one you choose within 0.3°C. Tetenal gives one cooler option for tank processors.
| Developer time | Kodak, trays | Kodak, small tubes with a prewet | Tetenal, tank processors |
|---|---|---|---|
| 0:45 | 35.0°C | 36.1°C | 35°C |
| 1:00 | 33.3°C | 34.4°C | |
| 1:20 | 30°C | ||
| 1:30 | 30.0°C | 31.1°C | |
| 2:00 | 27.2°C | 28.3°C |
If you lengthen the developer time, Kodak says to lengthen the bleach-fix by the same amount. Tetenal gives at least 1 minute of bleach-fix at 30°C.
Room temperature: what we found. We looked for a maker's developer time at ordinary room temperature, about 20°C, and did not find one. This is what the sheets do give.
- Kodak: the coolest pair is 2 minutes at 27.2°C in trays, or at 28.3°C in small tubes with a prewet
- Tetenal: 1 minute 20 seconds at 30°C
- Bellini and ADOX: 35°C only
- Kodak's drift-by table does cover a processor standing at 20.0°C, but it does so by starting the solution at 41.1°C, so the development itself still averages 35°C
Printers do report working at room temperature with longer times. No maker read for this guide publishes a time for it, so any figure would be someone's own experiment, and this guide does not give one. If you try it, test it as you would any change: hold the temperature and time the same from print to print, and expect to find your own filter pack.
Keeping the temperature steady
Solutions cool while they are in a drum. For processors that cannot hold 35°C, Kodak describes a "drift-by" method: start with the solution warmer than 35°C so that its average temperature over the step is 35°C. Kodak's starting points are below. Check the solution as it comes out, and adjust until the start and end temperatures average 35°C.
| Processor temperature | Start the solution at |
|---|---|
| 32.3°C | 36.1°C |
| 30.0°C | 37.1°C |
| 25.0°C | 39.1°C |
| 20.0°C | 41.1°C |
Whatever method you use, do it the same way each time. Tetenal's leaflet puts it plainly: colour development should always be done at the same temperature and for the same length of time. The bleach-fix is less fussy. Tetenal says a swing of 3°C either way, or small changes in time, will not significantly affect the result.
Stop bath
A stop bath between developer and bleach-fix is optional in trays. Kodak says to add one, with a 30 second wash after it, if developer carried over into the bleach-fix leaves marks or streaks. Tetenal recommends one because it conserves the bleach-fix and prevents magenta streaks.
Kodak's stop bath is 28 ml of glacial acetic acid per litre of water. Tetenal gives 2 to 3% acetic acid. A black and white stop bath made from acetic acid is the same chemical; glacial acetic acid itself is corrosive, so buy it ready diluted if you can.
Keep bleach-fix out of the developer
Kodak warns that "even minute amounts of bleach-fix can severely contaminate the developer". Use a separate jug for mixing the developer, keep a separate tray or measure for each bath, and rinse and dry the drum, its lid and your gloves between prints.
Wash and dry
Kodak's final wash is 1 minute 30 seconds, in running water or three changes of 30 seconds, and longer is acceptable. Dry the print in air or with warm air: Kodak's limit is 96°C. Kodak says not to ferrotype its papers and not to dry them in contact with plastic sheeting.
Making a print: the order of work
With the chemistry at temperature and the room dark, a colour print is made in a fixed order: exposure first, then colour, then the final print. Kodak's paper data sheet sets it out in this order: make a test print, judge its density, then judge its colour, change the filter pack, and adjust the exposure for the new pack. The sections after this one follow the same order.
Choose a well exposed negative with something neutral in it: a grey wall, white clothing, a road. A neutral tone shows a cast plainly, and a strongly coloured object hides one.
Mix the chemistry by the kit's instructions and bring the developer to your chosen temperature in a water bath. Set out the drum or trays in order.
Put the negative in the carrier, mask it, and compose and focus on the easel with the room lights off, as you would for black and white.
Set the starting filter pack and stop the lens down as you would for black and white.
In total darkness, expose a test strip across an important part of the picture.
Process the strip fully, including the wash, and dry it.
Under your viewing light, pick the step with the right density. Leave the colour until the density is right.
At that exposure, make a ring-around: a set of small test exposures, each with one change to the filter pack. Process and dry them, and pick the one whose neutral areas are closest to neutral.
Set that pack, adjust the exposure for the change, and make a small whole-frame test print. If it still has a cast, repeat step 7 with smaller changes.
When the density is right and the neutral areas are neutral, write the pack, aperture and time in your notebook and make the final print.
Expect to go round steps 7 and 8 more than once before the first good print. Each round teaches you how far a change on the dials moves the colour.
Choosing a starting filter pack
A filter pack is written as numbers and letters: 40M + 50Y means 40 units of magenta and 50 of yellow. Kodak's starting packs use magenta and yellow only, with no cyan.
| Paper | Maker's starting pack |
|---|---|
| Kodak Endura Premier | 40M + 50Y |
| Kodak Portra III (discontinued) | 45M + 45Y |
| Fujicolor Crystal Archive Type CA | None given in the data sheet |
| ADOX Color Mission | None found |
If your paper's maker gives no starting pack, Kodak's figures are a reasonable place to begin: somewhere near 40 to 45 magenta and 45 to 50 yellow, with cyan at zero. The first print will almost certainly have a cast. That is expected: the maker's pack is only a starting point for a test print.
Keep cyan at zero
A pack that contains all three colours also contains neutral density: grey that lengthens the exposure and does nothing for colour. Kodak's method is to take the smallest of the three values away from all of them. Its example: 10C + 40M + 50Y becomes 30M + 40Y, which gives the same colour with more light.
Finding the exposure with a test strip
A colour test strip is made the same way as a black and white one, in the dark, with the starting filter pack in place. See Print Exposure Basics for the method. The printing calculator will work out a series of times in even steps.
- Process and dry every strip exactly as you will process the final print. A strip pulled early tells you nothing. Darryl Nicholas, in Shutterbug's darkroom column, says a wet print cannot be judged for colour with any precision, and dries his with a hair dryer in a minute or two. Abel Rico's guide on Emulsive says the same: dry the test before you evaluate it.
- Read the strip for density only. Kodak's order is firm: judge density first, then colour. If the best step is too light, open the lens or lengthen the time. If it is too dark, close the lens or shorten the time.
- Aim for a time you can repeat. Nicholas suggests steps about half a stop apart, such as 2, 3, 5, 8, 12 and 18 seconds, and then changing the aperture so the chosen time is around 10 to 12 seconds.
Nicholas also suggests doing the colour tests that follow at a density a little darker than the final print, about half a stop, because a slight cast is easier to see in a darker print. Colour is hard to read from a narrow strip in any case, which is why the next stage uses larger pieces.
Balancing the colour
Printing from a negative reverses everything, colour included. To make a black and white print lighter you give it less light. In the same way, to remove a colour from a print you add that colour to the filter pack. A print that is too magenta needs more magenta filtration.
Reading a cast
This table is Kodak's, from its paper data sheet. The middle column is the correction that keeps cyan out of the pack; the last column is the equivalent Kodak also gives.
| If the print is too | Change the pack like this | Or, the equivalent |
|---|---|---|
| Magenta | Add magenta | Subtract cyan and yellow |
| Yellow | Add yellow | Subtract magenta and cyan |
| Red | Add magenta and yellow | Subtract cyan |
| Cyan | Subtract magenta and yellow | Add cyan |
| Green | Subtract magenta | Add cyan and yellow |
| Blue | Subtract yellow | Add cyan and magenta |
Two things make this easier to remember.
- The dial colours are their own cure. If the cast is the colour of one of the dials you are using, turn that dial up.
- Each dial colour has an opposite. Green is the opposite of magenta, blue of yellow, red of cyan. If the cast is the opposite of a dial, turn that dial down. Red is magenta and yellow together, so a red cast needs both turned up, and a cyan cast needs both turned down.
Naming the cast is the hard part. Look at the neutral areas and the lighter mid-tones, not at strongly coloured objects. Kodak made a kit for this purpose, the Color Print Viewing Filter Kit: 18 viewing filters with instructions for working out the filter change from a test print. It is no longer made, so look for a used one.
The ring-around test
A ring-around is a set of small test exposures of the same part of the picture, all at the same aperture and time, each with one change to the filter pack. It shows you which way the colour is off and roughly how far, without your having to name the cast first. You make it after the test strip and before the final print.
Nicholas describes it as a series of small images on one sheet of paper: pick the best, then start the next ring-around from its settings, getting closer each time. He recommends it over judging a single test print and guessing the correction, because a wrong guess costs another print each time.
- Keep the aperture and time you found with the test strip. Changing the exposure as well would give you two things to judge at once.
- Expose one piece at your current pack. This is the centre of the ring.
- Expose six more pieces, each with one change from the current pack, using the same size of change for all six. Use 10 units if the centre is close and 20 if it is far off.
- Use sections of one sheet, uncovered in turn under a piece of card, or small pieces cut from a sheet in the dark. Write the plan in your notebook before the lights go out and keep the pieces in that order.
- Process the pieces as you will process the final print, and dry them.
- Under your viewing light, lay the six round the centre piece and find the one whose neutral areas are closest to neutral. Its pack is your new pack. If the best answer lies between two pieces, set the pack halfway between them.
| Change from the current pack | Corrects a print that is too |
|---|---|
| More magenta | Magenta |
| Less magenta | Green |
| More yellow | Yellow |
| Less yellow | Blue |
| More magenta and more yellow | Red |
| Less magenta and less yellow | Cyan |
If the best piece still has a cast, make a second ring-around from the new pack with half the step.
If you can already name the cast, Nicholas gives a shorter test. Change only the dial that controls that colour, 5 units at a time, across a row of exposures, until the cast has tipped over into its opposite: from too green to too magenta, for example. The right setting is midway between the last piece that is clearly too green and the first that is clearly too magenta.
How big a change to make
The makers' paper sheets say which way to move the pack but not how far. The one set of figures we found is in an older training text, the Basic Photography Course hosted by DOFMaster, in its chapter on colour printing.
| How far off the print is | Change to the pack |
|---|---|
| Slightly | 05 or 10 units |
| Moderately | 15 or 20 units |
| Too far to estimate | Try 30 units |
The same text gives a rule for viewing filters. Look at the lighter middle tones of the test print through the filters, find the one that makes them look right, and change the pack by half that filter's value. A 20 viewing filter that looks right means a change of 10. It warns that viewing filters overcorrect the highlights and undercorrect the shadows, which is why the lighter middle tones are the ones to judge.
These figures are a starting point from one source, not a maker's specification. Your own ring-arounds will soon show you what 10 units looks like on your paper. If a colour cast will not go away whatever you do with the filters, the cause may be in the process or the negative: see Common Faults below.
How exposure changes when filtration changes
Filters absorb light, so changing the pack changes the exposure. A print that had the right density before a colour correction can come out too light or too dark after it. Within a ring-around the changes are small and the exposure stays the same. Make this adjustment once you have chosen the new pack, before the whole-frame test print.
With a colour head, Kodak's rule of thumb is:
- Magenta: change the exposure time by 1% for every unit of magenta you change. Add 20M, and the time goes up by 20%. Take 20M away, and it comes down by 20%.
- Yellow: changes do not usually affect the density of the print.
- Cyan: use the factors for cyan in the table below as a starting point.
With CP filters in a drawer, Kodak gives a factor for each filter.
| Filter | Factor | Filter | Factor | Filter | Factor |
|---|---|---|---|---|---|
| 05Y | 1.1 | 05M | 1.2 | 05C | 1.1 |
| 10Y | 1.1 | 10M | 1.3 | 10C | 1.2 |
| 20Y | 1.1 | 20M | 1.5 | 20C | 1.3 |
| 30Y | 1.1 | 30M | 1.7 | 30C | 1.4 |
| 40Y | 1.1 | 40M | 1.9 | 40C | 1.5 |
| 50Y | 1.1 | 50M | 2.1 | 50C | 1.6 |
When you add a filter, multiply the exposure time by its factor. When you remove one, divide by its factor. If you change two or more filters, multiply their factors together first. Kodak notes that you may need to adjust these factors for your own equipment, so treat the result as the time for the next test, not as a final answer.
If you change the size of the print as well, the print exposure calculator works out the new time for the new enlarger height.
The final print
When a whole-frame test print has the right density and its neutral areas are neutral, make the final print at the same pack, aperture and time. Process, wash and dry it exactly as you did the tests, then check it under the viewing light.
Write down the filter pack, aperture, time, paper and print size. A negative you have balanced once can be printed again from your notes, and they give you a closer starting pack for the next negative than the maker's figure does. The Basic Photography Course gives the same advice: start from a filter pack already established on your own equipment where there is one.
A ring-around to keep
Keep the test pieces from the session and write the filter pack on the back of each. Laid round the final print, they are the start of a reference ring-around: a set of prints from one negative with a known colour error in each direction.
Kodak published printed ring-around charts for this purpose. Peter Bargh, writing for ePHOTOzine, and David Kilpatrick, in Cameracraft, both describe making your own once you have one good print: prints from the same negative shifted by 10 and 20 units towards each of the six colours, labelled and mounted round the good print. Kilpatrick mounts his on neutral grey board. Fujifilm's data sheet for Type CA names the "ring around print" method as a way of setting up printing conditions.
Its use comes in later sessions. When a test print from another negative has a cast you cannot name, hold it beside the set and find the print it most resembles. The label tells you which way your pack is off, and roughly how far. The Basic Photography Course says to match your test print as closely as you can to one of the prints in the set, and adds that a ring-around helps most when the test print is far from correct.
Common faults
Most first-session problems come from four causes: light reaching the paper, developer temperature, bleach-fix in the developer, or too little solution in the drum. This table is from Tetenal's leaflet, with Kodak's notes added where they apply.
| What you see | Likely cause | What to do |
|---|---|---|
| A cast that no filter change removes | An unsuitable safelight, or light from LEDs | Work in total darkness and cover every light |
| Blue or magenta colour shifts | Developer contaminated with bleach-fix | Mix fresh developer. Clean measures, mixing jugs and the drum lid |
| Blacks that look blue | Developer too cool, time too short, too little agitation, or developer over-diluted or exhausted | Raise the developer temperature by 1°C or lengthen the time by 10 to 20%; check the dilution; mix fresh |
| Light and dark streaks, blue stains | Too little solution in the drum, or the drum not level | Use the volume the drum's maker gives, and level the drum |
| Magenta streaks | Uneven stopping as the bleach-fix goes in | Use a stop bath after the developer |
| Grey mottle or a dirty grey veil | Bleach-fix time too short, or bleach-fix exhausted | Lengthen the bleach-fix, or bleach-fix the print again |
| Spots | A wet drum, or condensation dripping from the processor lid (Kodak) | Dry the drum fully between prints and wipe the lid |
| Colour changes from one print to the next | Developer temperature or time drifting (Kodak) | Hold the developer within 0.3°C and use the same time every run |
For more on each of these, the Fix section works from the symptom to the cause:
- My RA-4 colour prints have a colour cast, or the colour changes from print to print
- Uneven or streaky prints
- Grey print borders and highlights
Some casts start in the negative, not in the print. Colour Negative Problems covers the faults that begin in film processing, and C-41 Colour Film Development at Home covers the process.
Buying paper and chemistry in the UK
Colour paper
Checked on 9 and 10 November 2026. Prices and stock change, so check before you plan a session. As far as we know, Fujifilm no longer sells Crystal Archive in cut sheets itself, so the sheets on sale are cut from rolls by other firms.
| Paper | What the maker says | Seen on sale in the UK |
|---|---|---|
| ADOX Color Mission RA-4 | High gloss, cut by ADOX from master rolls of another maker's paper. ADOX does not name the maker; a UK supplier says it is Fujifilm Crystal Archive, and in Silverlog's own printing it behaves like it | Firstcall Photographic: 5 x 7 in to 20 x 24 in. 100 sheets of 8 x 10 in were £53.99 and in stock |
| Fujicolor Crystal Archive Type CA | Designed for both analogue and digital printers. Glossy, lustre or matte | Nik & Trick lists "Fuji Crystal Archive" cut sheets in lustre and glossy from 10 x 8 in, from £89.99 for 100 sheets. Papercut lists "Fuji Crystal Archive" in gloss and matt, 8 x 10 in to 12 x 16 in, from £40.00 for 50 sheets, and calls it its entry-level paper for learning. Neither listing says which Crystal Archive type the sheets are |
| Fujicolor Crystal Archive Supreme | For analogue and digital printers, on a thicker base | Not seen as cut sheets at the shops checked |
| Kodak Endura Premier | Kodak's data sheet includes enlarger printing, but lists roll formats only | Rolls only, so you would cut your own sheets in the dark |
The shops checked were Firstcall Photographic, Nik & Trick, Parallax and Papercut. Papercut is a small North London firm that sells Fujifilm paper in cut sheets, cut to within 3 mm of the stated size.
Papercut also sells two Fujifilm papers by name: DPII in gloss and matt, 8 x 10 in to 20 x 24 in, from £45.00 for 50 sheets, and Maxima, 12 x 16 in to 20 x 24 in, from £87.00 for 50 sheets. Here the maker and the shop differ. Fujifilm's data sheets describe both papers as designed only for digital output. Papercut calls DPII "the standard choice for hand-printing colour images in the darkroom". Both statements are given so you can weigh them: the maker makes no promise for enlarger printing on these two papers, and a shop that sells to darkroom printers says DPII is what they use. All the colour papers Silverlog has checked are in the darkroom papers list.
Store unopened paper cool. Kodak gives 4 to 24°C for Endura Premier; Fujifilm gives below 10°C for long storage of Type CA. Both say to let refrigerated paper warm up in its sealed packet before you open it, so that moisture does not condense on it.
RA-4 chemistry
Checked on 9 November 2026.
| Kit | Makes | Maker's capacity | Keeping, mixed | Seen on sale in the UK |
|---|---|---|---|---|
| ADOX RA-4 kit | 2.5 litres each of developer and bleach-fix | 5 m², about 100 sheets of 8 x 10 in | One month in full, well closed bottles | Firstcall Photographic, £28.00, in stock |
| Bellini RA-4 kit | 5 litres each of developer and bleach-fix, plus stabiliser | 10 m² | Not given on the data sheet | Firstcall Photographic, £38.99; stock unclear on the day |
| Tetenal Colortec RA-4 Print Kit RT | 5 litres each | 9 to 10 m², about 230 sheets of 18 x 24 cm | 12 weeks fresh, 8 weeks half used | Not found in stock at the UK shops checked |
| Kodak Ektacolor RA | 1 gallon or 10 litre sizes | 16 prints of 8 x 10 in per litre in trays | Developer 6 weeks and bleach-fix 8 weeks in full glass bottles | Not checked |
The capacity figures do not agree with each other. A litre covers about 2 m² by the ADOX, Bellini and Tetenal figures, which is close to 40 sheets of 8 x 10 in, while Kodak recommends 16 sheets per litre for tray work. Kodak adds that "in some noncritical applications" up to 40 prints may be possible. Treat the lower figure as the safe one for prints that matter.
Kodak's keeping times assume storage at 18 to 24°C. A part-filled bottle of Kodak developer keeps 3 weeks, and developer left in an open tray should not be used after 4 hours.
Safety
Tetenal's safety data sheets for its RA-4 kit show what the two baths contain. Other makers' kits differ in detail, so read the sheet for the kit you buy.
- Colour developer concentrate contains the developing agent CD-3. Tetenal classifies the concentrate as harmful if swallowed (H302), able to cause an allergic skin reaction (H317) and toxic to aquatic life with long lasting effects (H411). Skin allergy is the reason to wear gloves every time, not only when mixing.
- The second developer part contains potassium carbonate and is classed as a skin and eye irritant (H315, H319).
- Bleach-fix contains ammonium thiosulphate and sodium metabisulphite, with a little acetic acid. Tetenal classes one part as causing serious eye damage (H318), so wear eye protection when you pour it.
- Stop bath is dilute acetic acid.
ADOX's safety data sheets for its RA-4 kit (2014) are close to Tetenal's but not the same. The developer concentrate is classed as harmful if swallowed (H302), irritating to skin and eyes (H315, H319), able to cause an allergic skin reaction (H317) and harmful to aquatic life with long lasting effects (H412). It contains the same developing agent, with diethylene glycol, potassium carbonate and a little sodium hydroxide. The bleach-fix sheet lists ammonium hydrogensulphite, ammonium thiocyanate and acetic acid, and classes the solution as causing serious eye irritation (H319).
Silverlog's chemical records give the official classifications for the pure substances:
| Chemical | Hazards |
|---|---|
| Acetic acidDanger | Flammable liquid and vapour.; Causes severe skin burns and eye damage. |
| Ammonium thiosulfate | Not classified as hazardous |
| Sodium metabisulfiteDanger | Harmful if swallowed.; Causes serious eye damage.; Contact with acids liberates toxic gas. |
| Potassium carbonateWarning | May cause respiratory irritation.; Causes skin irritation.; Causes serious eye irritation. |
Classifications from the European Chemicals Agency (official EU classification where one exists, otherwise the one agreed by REACH registrants or most often notified). Read the safety data sheet that comes with your chemicals, and dispose of them in line with local regulations.
Tetenal's leaflet also advises ventilation at all times, washing your hands after work, keeping chemicals away from food and out of reach of children, and labelling every storage bottle clearly. If a solution reaches your eyes, rinse with water for 15 minutes and see a doctor.
Disposal in the UK
Two sources apply, and they differ, so both are given.
Ilford's advice for home users in the UK is that local authorities should accept small quantities of used chemicals at Household Waste and Recycling Centres, where there is usually a chemical cupboard. Bottle each chemical separately, label it, and do not mix chemicals for disposal. Some councils collect on request. Ilford says that if no such route is available, small amounts should be flushed down the drain with plenty of water. It advises against putting photographic chemicals into a septic tank.
Tetenal's and ADOX's safety data sheets for their RA-4 developers say not to put them out with household rubbish and not to let them reach the sewage system, and to dispose of them according to official regulations. Tetenal says the same of its bleach-fix, and ADOX says its bleach-fix must not reach ground water or the sewage system.
Taking used developer and bleach-fix to your council's recycling centre satisfies all three. Ring the centre first: arrangements vary between councils. Used bleach-fix also carries the silver removed from the paper, which is one more reason to keep it out of the drain.
Schools, colleges, community darkrooms and businesses are not home users. Ilford says business and trade users should use a licensed waste disposal operator.
Summary
- Work in total darkness. Kodak and Fujifilm allow a dim amber safelight only when unavoidable, and both warn that it can affect the print
- Hold the developer temperature within 0.3°C. At 35°C the developer and bleach-fix take 45 seconds each; Kodak also gives longer times down to 27.2°C. No maker we read gives a room-temperature time
- Start near 40M + 50Y and keep cyan at zero
- Find the exposure first with a test strip, then balance the colour
- Judge every test dry, under a 5000 K light
- Balance the colour with a ring-around before the final print: small test exposures with one filter change each
- To remove a colour from the print, add that colour to the filter pack
- Change the pack by 05 or 10 units for a slight cast and 15 or 20 for a moderate one
- Allow for the change in exposure when you change magenta
- Keep bleach-fix out of the developer
- Take used chemistry to a Household Waste and Recycling Centre
The first session is mostly tests. Keep them, labelled with their filter packs: they are the start of a ring-around you can refer to, and the fastest way to learn what a change of 10 units looks like on your own equipment.
Sources
Checked 9 and 10 November 2026.
- Tray, Drum, and Rotary-Tube Processing with KODAK EKTACOLOR RA Chemicals (J-39, December 2017), Kodak Alaris
- KODAK PROFESSIONAL ENDURA Premier Paper technical data (E-4070, December 2017), Kodak Alaris
- KODAK PROFESSIONAL PORTRA III Paper technical data (E-140, July 2002), Eastman Kodak. A discontinued paper; used for the colour correction table and filter factors
- How Safe Is Your Safelight? A Guide to Darkroom Illumination (K-4), Eastman Kodak
- Fujicolor Crystal Archive Paper Type CA data sheet (November 2018), Fujifilm
- Tetenal Colortec RA-4 Professional Print Kit RT instructions, Tetenal, hosted by Macodirect
- Tetenal Colortec RA-4 Professional Print Kit RT safety data sheets (2014), Tetenal, hosted by Macodirect
- Bellini Foto Kit RA4 technical data sheet, Bellini Foto, hosted by Macodirect
- Colour paper developing Kit RA-4, ADOX
- ADOX RA-4 Print Kit Professional safety data sheets (2014), ADOX, hosted by Nik & Trick
- Basic Photography Course, chapter 12, Color Printing, pages 12-7 and 12-8, DOFMaster. An older training text; used for the size of a filter change and the use of a ring-around
- The Darkroom: Printing Color Negatives, Darryl C. Nicholas, Shutterbug, 1 August 2000. Used for the order of work, the ring-around test, and judging prints dry
- Making colour prints in the darkroom: welcome to RA-4 printing, Abel Rico, Emulsive, 15 October 2019. Used for drying test prints before judging them
- Making a colour darkroom ringaround chart, Peter Bargh, ePHOTOzine, 12 January 2002. Used for the reference ring-around
- Judging colour in the darkroom, David Kilpatrick, Cameracraft, first published 1996. Used for the reference ring-around
- ADOX Color Mission RA-4 paper, Fotoimpex
- General health and safety advice: waste disposal for photographic products, Ilford Photo
- ADOX Color Mission RA-4 Paper 8 x 10 in, Firstcall Photographic, for UK price and stock
- Adox RA4 Professional Kit 2.5L, Firstcall Photographic, for UK price and stock
- Bellini RA4 Kit 5L, Firstcall Photographic, for UK price and stock
- Fuji Crystal Archive Colour Paper for RA4 Process, Nik & Trick Photo Services, for UK price
- Fuji colour paper in cut sheets, Papercut, for UK prices and its description of DPII