Free course · 8 steps · Two darkroom sessions
Make your first colour print
Make a colour print from your own colour negative in a darkroom: find the exposure, balance the colour with a ring-around, then make a neutral final print.
For anyone who has made a black and white print. You don't need your own darkroom, but ask before you book: not every community darkroom is set up for colour.
- Refresh your enlarger and test strip routine, to do
- Gather the paper, chemistry and equipment, to do
- Practise working in the dark, to do
- Run the process on a test sheet, to do
- Find the exposure with a test strip, to do
- Balance the colour with a ring-around, to do
- Work out what went wrong, to do
- Make the final print, to do
What you need
- Access to a darkroom with a colour enlarger
- RA-4 colour paper
- An RA-4 chemistry kit and a stop bath
- A print drum or a set of trays
- An accurate thermometer and a water bath
- Nitrile gloves and eye protection
Safety
Official hazard classifications for the chemicals this course uses. Read the chemicals pages for the details.
| Chemical | Hazards |
|---|---|
| Acetic acidDanger | Flammable liquid and vapour.; Causes severe skin burns and eye damage. |
| Ammonium thiosulfate | Not classified as hazardous |
| Sodium metabisulfiteDanger | Harmful if swallowed.; Causes serious eye damage.; Contact with acids liberates toxic gas. |
| Potassium carbonateWarning | May cause respiratory irritation.; Causes skin irritation.; Causes serious eye irritation. |
Classifications from the European Chemicals Agency (official EU classification where one exists, otherwise the one agreed by REACH registrants or most often notified). Read the safety data sheet that comes with your chemicals, and dispose of them in line with local regulations.
Dispose of used chemistry according to the manufacturer's safety data sheet and your local council and water company rules.
Steps
1Refresh your enlarger and test strip routine
Colour printing uses the same enlarger, easel and test strips you already know from black and white printing, but in the dark and with less room for error. Those habits need to be automatic before you add colour.
Do this now
Read the test strip and evaluation sections of the guide again. If you have not been in a darkroom for a while, spend a session printing in black and white first to get your routine back.
Checkpoint: You can set up an enlarger and make and read a test strip without thinking about each step.
2Gather the paper, chemistry and equipment
You need a way to filter the enlarger's light, colour paper, a developer and a bleach-fix, and a way to hold the developer at a steady temperature. The guide lists what was on sale in the UK when it was last checked.
Do this now
Read What You Need in the guide. Check that the enlarger you will use has a colour head or a filter drawer, then choose a paper and a chemistry kit and read the kit's safety data sheet.
Checkpoint: You have paper, chemistry and a way to process it, and you know what the safety data sheet asks of you.
3Practise working in the dark
The makers say to handle colour paper in total darkness, so everything from opening the box to closing the drum is done by touch. A fixed layout and a practised routine replace the safelight.
Do this now
Read Working in the Dark. With the lights on, lay out your paper, easel and drum or trays, then cover every stray light and rehearse the whole sequence with a scrap sheet and your eyes closed.
Checkpoint: You can take a sheet from the box, expose it and get it into the first bath or a closed drum in the dark.
4Run the process on a test sheet
The process is short, and the developer's temperature and time must be the same every run. The steps below are Kodak's for a drum; the guide also gives tray times, cooler options and the other makers' figures.
Do this now
Mix the chemistry by your kit's instructions, wearing gloves and eye protection in a ventilated room, and never eat or drink where you work. Bring the developer to temperature in a water bath, then process one exposed sheet, timing each step with the process timer. Follow your own kit's leaflet where it differs from the table.
Kodak Ektacolor RA, rotary tube or drum at 35°C Step Time Temp Agitation Prewet 0:30 35°C Rotary, in the processor with clean water Developer 0:45 35°C Rotary Stop bath 0:30 35°C Rotary Wash 0:30 35°C Rotary Bleach-fix 0:45 35°C Rotary Wash 1:30 35°C Continuous flow with one complete change every 30 s, or three 30 s batch washes From Tray, Drum, and Rotary-Tube Processing with KODAK EKTACOLOR RA Chemicals. Run it step by step in the process timer.
Checkpoint: You have processed a sheet of colour paper from developer to dry print with the temperature under control.
5Find the exposure with a test strip
Exposure comes before colour. A test strip at the maker's starting filter pack tells you the exposure, and a print that is too light or too dark cannot be judged for colour. Every test is judged dry, under the same viewing light.
Do this now
Set the starting filter pack from the guide, make a test strip across an important part of the picture, then process it fully and dry it. Under your viewing light, choose the step with the right density and note the time and aperture. Leave the colour for the next step.
Checkpoint: You have an exposure that gives the right density at the starting filter pack.
6Balance the colour with a ring-around
Printing from a negative reverses colour as well as tone, so you remove a cast by adding that colour to the filter pack. A ring-around is a set of small test exposures with one filter change each: it shows which way the colour is off, and how far, before you commit a full sheet. Changing the pack also changes the exposure, most of all with magenta.
Do this now
At the exposure you found, make the ring-around described in the guide: one piece at your current pack and six more with one change each. Process and dry them, and pick the one whose neutral areas are closest to neutral. Set that pack, adjust the exposure as the guide describes, and make a small whole-frame test print. Repeat with smaller changes until the neutral areas are neutral, writing down every pack you try.
Checkpoint: You have a whole-frame test print with the right density and neutral colour, and you can say which filter change removes which cast.
7Work out what went wrong
Not every fault is a filtration fault. A cast that no ring-around removes, colour that drifts between prints and streaks all have a small number of causes: stray light, developer temperature, contaminated developer or too little solution.
Do this now
Compare your test prints with the causes on the Fix page and the fault table in the guide. Decide whether each problem comes from filtration, light, temperature or contamination before you change anything.
Checkpoint: You can tell a filtration problem from a processing or fogging problem on a colour print.
8Make the final print
The final print repeats the last good test exactly: the same filter pack, aperture, time and processing. Your notes and your labelled test pieces are what make the next negative quicker.
Do this now
Make your final print, process and dry it as you did the tests, and check it under the viewing light. Record its filter pack, aperture and time. Write the pack on the back of each ring-around piece and keep them with the print as a reference, then bottle and label the used chemistry for disposal as the guide sets out.
Checkpoint: You have a neutral colour print, the notes to repeat it and a labelled set of test pieces to judge future prints against.